JetHome docs/Controllers — English @ Weblate: 1-Wire Data

Zen

Translation

Russian

English

Review state

Translated

Skip

	Russian	English	Actions
	GPIOA_2	GPIOA_2
	540 (454)	540 (454)
	28	28
	1-Wire	1-Wire
	:ref:`linux_onewire`	:ref:`linux_onewire`
	:ref:`homeassistant_onewire`	:ref:`homeassistant_onewire`
	Начиная с ревизии 1.5 материнской платы для подключения шины 1-Wire используется 3-контактный разъем с шагом 3.5мм	Starting with the 1.5 motherboard revision, a 3.5mm pitch 3-pin connector is used for the 1-Wire bus connection.
	Начиная с ревизии 1.7 материнской платы используется программная реализация 1-Wire на GPIO	Starting with revision 1.7 of the motherboard, the software implementation of 1-Wire on GPIO is used
	Ввиду особенности программной реализации 1 Wire в Linux максимальное к-во устройств на одной шине - 5шт.	Due to the peculiarity of the software implementation of 1 Wire in Linux the maximum number of devices on one bus is 5pcs.
	Разъем 1-Wire 3x3.5 мм	1-Wire 3x3.5 mm connector
	Назначение выводов:	Pin assignment:
	Назначение	Destination
	Описание	Description
	+5V	+5V
	Выход питания +5В (для питания внешних устройств 1-Wire)	Power output +5V (for powering external devices 1-Wire)
	1-Wire Data	1-Wire Data
	Шина данных 1-Wire	1-Wire data bus
	GND	GND
	Общий провод 1-Wire	Common 1-Wire
	Разъем 1-Wire RJ22	1-Wire RJ22 connector
	Общий провод питания	Common power lead
	1-Wire GND	1-Wire GND
	RS-485 (Modbus)	RS-485 (Modbus)
	:ref:`linux_modbus`	:ref:`linux_modbus`
	Контроллер имеет два порта RS-485, реализованных с использованием микросхем преобразователя интерфейса USB-UART:	The controller has two RS-485 ports implemented using USB-UART interface converter chips:
	Ревизия v3.0 и ниже: Silicon Labs CP2104 или CP2105	Revision v3.0 and below: Silicon Labs CP2104 or CP2105
	Ревизия v3.5 и выше: Silicon Labs CP2102N с автоматическим переключением режима приёма/передачи и гальванической изоляцией через трансиверы TDA51S485HC	Revision v3.5 and above: Silicon Labs CP2102N with automatic receive/transmit mode switching and galvanic isolation via TDA51S485HC transceivers
	В операционной системе данные устройства отображаются как ``/dev/ttyUSB0`` и ``/dev/ttyUSB1``.	The operating system displays these devices as ``/dev/ttyUSB0`` and ``/dev/ttyUSB1``.
	Концы шины RS-485 должны быть терминированы резисторами 120 Ом с обоих концов.	The ends of the RS-485 bus must be terminated with 120 Ohm resistors at both ends.
	Для упрощения монтажа контроллер имеет встроенные терминаторы, подключаемые к линиям RS-485 с помощью перемычек (джамперов), расположенных рядом с клеммами RS-485.	To simplify installation, the controller has built-in terminators that connect to the RS-485 lines with jumpers located near the RS-485 terminals.
	Часы реального времени (RTC)	Real Time Clock (RTC)

Loading…

None

String added in the repository

Russian

English 11 characters editedCurrent translationState: Translated

04/29/2026

Browse all string changes

Things to check

Unchanged translation

Source and translation are identical.

Reset

Glossary

Russian	English
No related strings found in the glossary.

Browse glossary JetHome docs

String information

Flags

rst-text

Unit identifier

9526

Source string location

../../includes/common/connectors/onewire_3pin.rst:7 • ../../includes/common/connectors/onewire_rj22.rst:11

String age

04/29/2026

Last updated

04/29/2026

Source string age

04/29/2026

Translation file gettext PO file

_locale/en/LC_MESSAGES/controllers.po, string 299

Shortcut	Action
`?`	Open available keyboard shortcuts.
`Alt` + `Home`	Navigate to the first translation in the current search.
`Alt` + `End`	Navigate to the last translation in the current search.
`Alt` + `PageUp` or `Ctrl` + `↑` or `Alt` + `↑` or `Cmd` + `↑` or	Navigate to the previous translation in the current search.
`Alt` + `PageDown` or `Ctrl` + `↓` or `Alt` + `↓` or `Cmd` + `↓` or	Navigate to the next translation in the current search.
`Ctrl` + `Enter` or `Cmd` + `Enter`	Submit current form; this works the same as pressing Save and continue while editing translation.
`Ctrl` + `Shift` + `Enter` or `Cmd` + `Shift` +`Enter`	Unmark translation as Needing edit and submit it.
`Alt` + `Enter` or `Option` + `Enter`	Submit the string as a suggestion; this works the same as pressing Suggest while editing translation.
`Ctrl` + `E` or `Cmd` + `E`	Focus on translation editor.
`Ctrl` + `U` or `Cmd` + `U`	Focus on comment editor.
`Ctrl` + `M` or `Cmd` + `M`	Shows Automatic suggestions tab.
`Ctrl` + `1` to `Ctrl` + `9` or `Cmd` + `1` to `Cmd` + `9`	Copies placeable of a given number from source string.
`Ctrl` + `M` followed by `1` to `9` or `Cmd` + `M` followed by `1` to `9`	Copy the machine translation of a given number to current translation.
`Ctrl` + `I` followed by `1` to `9` or `Cmd` + `I` followed by `1` to `9`	Ignore one item in the list of failing checks.
`Ctrl` + `J` or `Cmd` + `J`	Shows the Nearby strings tab.
`Ctrl` + `S` or `Cmd` + `S`	Focus on search field.
`Ctrl` + `O` or `Cmd` + `O`	Copy the source string.
`Ctrl` + `Y` or `Cmd` + `Y`	Toggle the Needs editing checkbox.
`→`	Browse the next translation string.
`←`	Browse the previous translation string.

Translation

Things to check

Unchanged translation

Glossary

String information

Flags

Details

Unit identifier

Source string location

String age

Last updated

Source string age

Translation file gettext PO file