JetHome docs/Controllers — English @ Weblate

Russian

Управление режимом загрузки осуществляется путем записи 0 или 1 в GPIO BOOT процессора (см. таблицу выше). Для модуля беспроводной связи Zigbee вход в режим загрузчика осуществляется при логическом уровне 0 на выводе BOOT во время сброса модуля Zigbee.

319 ../../controllers/linux/includes/platforms/j100/wireless_module.rst:1
	Russian Модуль подключен к порту ``UARTA0_B`` процессора, аппаратное управление приемом/передачей (линии RTS и CTS) не используется. Устройство отображается в системе как ``/dev/ttyAML2``.
	English The module is connected to the ``UARTA0_B`` port of the processor, hardware control of reception/transmission (RTS and CTS lines) is not used. The device is displayed in the system as ``/dev/ttyAML2``. 205/1840 · 184 Review state Translated
320 ../../controllers/linux/includes/platforms/j100/wireless_module.rst:5
	Russian Для управления беспроводным модулем используются GPIO процессора, которые подключены к линиям ``RESET`` и ``BOOT`` беспроводного модуля (см. :ref:`linux_gpio_outputs`):
	English The GPIOs of the processor are used to control the wireless module, which are connected to the lines ``RESET`` and ``BOOT`` of the wireless module (see :ref:`linux_gpio_outputs`): 181/1700 · 170 Review state Translated
321 ../../controllers/linux/includes/platforms/j100/40_pin_connector.rst:50 • ../../controllers/linux/includes/platforms/j100/wireless_module.rst:11
	Russian GPIOA_15
	English GPIOA_15 8/100 · 8 Review state Translated
322 ../../controllers/linux/includes/platforms/j100/wireless_module.rst:11
	Russian 553 (467)
	English 553 (467) 9/100 · 9 Review state Translated
323 ../../controllers/linux/includes/platforms/j100/wireless_module.rst:11
	Russian 41
	English 41 2/100 · 2 Review state Translated
324 ../../controllers/linux/includes/platforms/j100/40_pin_connector.rst:54 • ../../controllers/linux/includes/platforms/j100/wireless_module.rst:12
	Russian GPIOA_10
	English GPIOA_10 8/100 · 8 Review state Translated
325 ../../controllers/linux/includes/platforms/j100/wireless_module.rst:12
	Russian 548 (462)
	English 548 (462) 9/100 · 9 Review state Translated
326 ../../controllers/includes/motherboards/pd76_r5_v1/connectors/40_pin.csv:1 • ../../controllers/includes/motherboards/pd76_r5_v2/connectors/40_pin.csv:1 • ../../controllers/linux/includes/platforms/j100/40_pin_connector.rst:55 • ../../controllers/linux/includes/platforms/j100/wireless_module.rst:12 • ../../controllers/mcu/includes/e1_cpu/connectors/40_pin.csv:1 • ../../controllers/mcu/includes/e1_cpu/wroom32_pinout.csv:1
	Russian 36
	English 36 2/100 · 2 Review state Translated
327 ../../controllers/linux/includes/platforms/j100/wireless_module.rst:17
	Russian Аппаратный сброс модуля беспроводной связи осуществляется путем записи логического уровня 1 в GPIO RESET процессора (см. таблицу выше). Возврат в рабочий режим осуществляется путем записи логического уровня 0 в GPIO RESET процессора.
	English Hardware reset of the wireless module is done by writing logic level 1 to GPIO RESET of the processor (see table above). Return to operation mode is performed by writing logical level 0 to GPIO RESET of the processor. 217/2330 · 233 Review state Translated
328 ../../controllers/linux/includes/platforms/j100/wireless_module.rst:20
	Russian Управление режимом загрузки осуществляется путем записи 0 или 1 в GPIO BOOT процессора (см. таблицу выше). Для модуля беспроводной связи Zigbee вход в режим загрузчика осуществляется при логическом уровне 0 на выводе BOOT во время сброса модуля Zigbee.
	English The boot mode is controlled by writing 0 or 1 to the GPIO BOOT of the processor (see table above). For the Zigbee wireless module, entering boot mode is done by writing a logic level 0 to the BOOT pin during a Zigbee module reset. 230/2520 · 252 Review state Translated
329 ../../controllers/linux/includes/platforms/j100/wireless_module.rst:23
	Russian Переключение режимов происходит при включении или аппаратном сбросе модуля. Поэтому после смены логического уровня на выводе BOOT модуля необходимо выполнить аппаратный сброс модуля.
	English Switching of modes takes place when the module is switched on or when it is hardware reset. Therefore, after changing the logical level on the BOOT pin of the module, you must perform a hardware reset of the module. 215/1820 · 182 Review state Translated
330 ../../controllers/linux/din_rail/d1.rst:165 • ../../controllers/linux/din_rail/d1p.rst:173 • ../../controllers/linux/din_rail/d1p_knx.rst:172 • ../../controllers/mcu/e1/jethub_e1_pd76_r5.rst:130 • ../../controllers/mcu/e1/jethub_e1_pd76_r5_ac.rst:153 • ../../controllers/mcu/e1/jethub_e1_pd76_r5_dc.rst:152
	Russian Внутренние разъёмы
	English Internal connectors 19/180 · 18 Review state Translated
331 ../../controllers/linux/din_rail/d1.rst:168 • ../../controllers/linux/din_rail/d1p.rst:176 • ../../controllers/linux/din_rail/d1p_knx.rst:175 • ../../controllers/mcu/e1/jethub_e1_pd76_r5.rst:138 • ../../controllers/mcu/e1/jethub_e1_pd76_r5_ac.rst:161 • ../../controllers/mcu/e1/jethub_e1_pd76_r5_dc.rst:160
	Russian Разъём 40-pin на процессорной плате
	English 40-pin connector on the processor board 39/350 · 35 Review state Translated
332 ../../controllers/linux/includes/platforms/j100/40_pin_connector.rst:2
	Russian Сигналы, выведенные на разъём расширения
	English Signals output to the expansion connector 41/400 · 40 Review state Translated
333 ../../controllers/linux/includes/platforms/j100/40_pin_connector.rst:4
	Russian Ethernet (x4 линии PHY)
	English Ethernet (x4 PHY lines) 23/230 · 23 Review state Translated
334 ../../controllers/linux/includes/platforms/j100/40_pin_connector.rst:5
	Russian Ethernet LED (х2 линии)
	English Ethernet LED (x2 lines) 23/230 · 23 Review state Translated
335 ../../controllers/linux/includes/platforms/j100/40_pin_connector.rst:6
	Russian USB (х2 линии)
	English USB (x2 lines) 14/140 · 14 Review state Translated
336 ../../controllers/linux/includes/platforms/j100/40_pin_connector.rst:7
	Russian SPI (х4 линии)
	English SPI (x4 lines) 14/140 · 14 Review state Translated
337 ../../controllers/linux/includes/platforms/j100/40_pin_connector.rst:8
	Russian I2C (х2 линии)
	English I2C (x2 lines) 14/140 · 14 Review state Translated
338 ../../controllers/linux/includes/platforms/j100/40_pin_connector.rst:9
	Russian x2 UART (х4 линии)
	English x2 UART (x4 lines) 18/180 · 18 Review state Translated

Shortcut	Action
`?`	Open available keyboard shortcuts.
`Alt` + `Home`	Navigate to the first translation in the current search.
`Alt` + `End`	Navigate to the last translation in the current search.
`Alt` + `PageUp` or `Ctrl` + `↑` or `Alt` + `↑` or `Cmd` + `↑` or	Navigate to the previous translation in the current search.
`Alt` + `PageDown` or `Ctrl` + `↓` or `Alt` + `↓` or `Cmd` + `↓` or	Navigate to the next translation in the current search.
`Ctrl` + `Enter` or `Cmd` + `Enter`	Submit current form; this works the same as pressing Save and continue while editing translation.
`Ctrl` + `Shift` + `Enter` or `Cmd` + `Shift` +`Enter`	Unmark translation as Needing edit and submit it.
`Alt` + `Enter` or `Option` + `Enter`	Submit the string as a suggestion; this works the same as pressing Suggest while editing translation.
`Ctrl` + `E` or `Cmd` + `E`	Focus on translation editor.
`Ctrl` + `U` or `Cmd` + `U`	Focus on comment editor.
`Ctrl` + `M` or `Cmd` + `M`	Shows Automatic suggestions tab.
`Ctrl` + `1` to `Ctrl` + `9` or `Cmd` + `1` to `Cmd` + `9`	Copies placeable of a given number from source string.
`Ctrl` + `M` followed by `1` to `9` or `Cmd` + `M` followed by `1` to `9`	Copy the machine translation of a given number to current translation.
`Ctrl` + `I` followed by `1` to `9` or `Cmd` + `I` followed by `1` to `9`	Ignore one item in the list of failing checks.
`Ctrl` + `J` or `Cmd` + `J`	Shows the Nearby strings tab.
`Ctrl` + `S` or `Cmd` + `S`	Focus on search field.
`Ctrl` + `O` or `Cmd` + `O`	Copy the source string.
`Ctrl` + `Y` or `Cmd` + `Y`	Toggle the Needs editing checkbox.
`→`	Browse the next translation string.
`←`	Browse the previous translation string.