User avatar jethome_iot_translator

Translation updated by source upload
Translation updated by source upload 09/15/2026
User avatar jethome_iot_translator

File uploaded
Processed 23 strings from the uploaded files (skipped: 0, not found: 0, updated: 23).
File upload mode: Update source strings 09/15/2026
User avatar jethome_iot_translator

Translation updated by source upload
Translation updated by source upload 09/15/2026
User avatar jethome_iot_translator

Changes committed
Changes committed 09/15/2026
User avatar jethome_iot_translator

Translation updated by source upload
Translation updated by source upload 09/15/2026
User avatar jethome_iot_translator

File uploaded
Processed 89 strings from the uploaded files (skipped: 0, not found: 0, updated: 89).
File upload mode: Update source strings 09/15/2026
User avatar jethome_iot_translator

Changes committed
Changes committed 09/15/2026
User avatar jethome_iot_translator

File uploaded
Processed 2026 strings from the uploaded files (skipped: 0, not found: 0, updated: 2026).
File upload mode: Update source strings 09/15/2026
User avatar jethome_iot_translator

Changes committed
Changes committed 09/15/2026
User avatar admin

Translation changed
Микросхема памяти *PSRAM* устанавливается в зависимости от комплектации контроллера.
When the controller is powered by USB, the controller firmware mode is setThe *PSRAM* memory chip is installed depending on the controller configuration.
09/15/2026
User avatar jethome_iot_translator

Changes committed
Changes committed 09/15/2026
User avatar jethome_iot_translator

Changes committed
Changes committed 09/15/2026
User avatar admin

Suggestion accepted
На процессорном модуле установлена микросхема *SPI NOR-Flash* памяти объемом *16 МБайт*. Микросхема Flash памяти подключена к следующим выводам микроконтроллера ESP32:
The processor module has a non-volatile *EEPROM* memory chip `AT24C64`_ (or equivalent) of *64Kbit* (*8 KBytes*).*SPI NOR-Flash* memory chip with a capacity of *16 MB*. The Flash memory chip is connected to the following pins of the ESP32 microcontroller:
09/15/2026
User avatar admin

Translation changed
Внешняя шина *I2C* доступна начиная с ревизии *1.4* материнской платы.
This periphe external *I2C* bus is available starting with motherboard revision v3.5revision *1.4* of the motherboard.
09/15/2026
User avatar admin

Suggestion accepted
Максимальный отдаваемый ток с клеммы питания ``1-WIRE`` - *0,5А*.
Maximum switchable current - *16output current from the power supply terminal ``1-WIRE`` - *0.5 A*.
09/15/2026
User avatar admin

Suggestion accepted
На плате установлен подтягивающий резистор на линию данных *1-Wire*, дополнительных внешних подтягивающих резисторов устанавливать не нужно. Рекомендуется подключать датчики *1-Wire* по трехпроводной схеме (включая линию питания).
AThe board has a pull-up resistor foron the `*1-Wire`* data line is installed on the board, so there's no need to install additional external pull-up resistors, no additional external pull-up resistors are required. It is recommended to connect *1-Wire* sensors using a three-wire scheme (including the power line).
09/15/2026
User avatar admin

Suggestion accepted
Адрес микросхемы *DS2482S-100* на внутренней шине *I2C* - ``0x18``.
The aAddress of the memory *DS2482S-100* microchip on the internal *I2C* bus is- ``0x5418``.
09/15/2026
User avatar admin

Translation changed
В контроллере предусмотрена возможность подключения внешних датчиков по шине *1-Wire*.
The controller haprovides the capability to connect external sensors via the `*1-Wire`* bus.
09/15/2026
User avatar admin

Translation changed
**Назначение контактов клеммы дискретных входов:**
Detection of events from all discrete inputs.**Purpose of the discrete input terminal contacts:**
09/15/2026
User avatar jethome_iot_translator

Resource updated
Parsing of the “_locale/en/LC_MESSAGES/zigbee.po” file was enforced. 09/15/2026

Search