User avatar mt:libretranslate

Suggestion added

The joystick and buttons of the display module are connected to the port expander of the display module, ports ``8`` ... ``14``. The logical level ``1` corresponds to the pressed button, so no inversion is required:

Suggested change:

The joystick and buttons of the display module are connected to the port expander of the display module, ports ``8`` …... ``14``. LThe logical level ``1`` corresponds to athe pressed button, so no inversion is not required:

Failing checks:

Inconsistent reStructuredText reStructuredText syntax error 09/15/2026
User avatar mt:libretranslate

Suggestion added

The states of relays and discrete inputs are deduced in two rows of three values; relays and inputs are assigned the identifiers ``relay 1`` ... ``relay 6`` and ``input 1`` ... ``input 6`` to refer to them from the lambda function.

Suggested change:

The states of relays and discrete inputs are deduced in two rows of three values; relays and inputs are assigned the identifiers ``relay 1`` ... ``relay 6`` and ``input 1`` ... ``input 6`` to refer to them from the lambda function.
09/15/2026
User avatar mt:libretranslate

Suggestion added

Discrete inputs are connected to the extender of motherboard ports, ports "8" ... "13". The logical level "1" corresponds to a closed entrance.

Suggested change:

Discrete inputs are connected to the extender of motherboard port expander, ports ``8`` … ``13``. Ls, ports "8" ... "13". The logical level ``1``"1" corresponds to a closed inputentrance.

Failing checks:

Inconsistent reStructuredText 09/15/2026
User avatar mt:libretranslate

Suggestion added

Relays are connected to the extender of the motherboard ports, the ports ``0`` ... ``5``.

Suggested change:

Relays are connected to the extender of the motherboard port expander,s, the ports ``0`` …... ``5``.
09/15/2026
User avatar mt:libretranslate

Suggestion added

Discrete inputs have **group galvanic isolation**: inputs are isolated from the rest of the controller elements, but are not isolated from each other and have one "COM" contact in common. Discrete inputs ``DIGITAL INPUT 1`, ``DIGITAL INPUT 6`` must be closed at the general contact ``COM`` located at the terminals of the discrete inputs. There is no need to connect the "COM" output with the "GND" output on the controller.

Suggested change:

Discrete inputs have **group galvanic isolation**: inputs are isolated from the rest of the controller elements, but are not isolated from each other and have one "COM" contact in common. Discrete inputs ``DIGITAL INPUT 1`, ``DIGITAL INPUT 6`` must be closed at the general contact ``COM`` located at the terminals of the discrete inputs. There is no need to connect the "COM" output with the "GND" output on the controller.

Failing checks:

Inconsistent reStructuredText 09/15/2026
User avatar mt:libretranslate

Suggestion added

"Relay 1" and "Relay 6".

Suggested change:

"Relay terminals ``RELAY 1``, ... ``RELAY 6``1" and "Relay 6".

Failing checks:

Inconsistent reStructuredText 09/15/2026
User avatar mt:libretranslate

Suggestion added

After restoring communication with the sensor, the thermostat returns to work on its own: the first value obtained is again checked for thresholds.

Suggested change:

After restoring communication with the sensor, the thermostat returns to work on its own: the first value obtained is again checked for thresholds.
09/13/2026
User avatar mt:libretranslate

Suggestion added

If the readings stop coming, the “timeout” filter itself publishes “NaN” after 30 seconds, which results in the same shutdown. The sensor survey period is *5 seconds*, i.e. activation occurs after six missed measurements.

Suggested change:

If the readings stop coming, the “timeout” filter itself publishes “NaN” after 30 seconds, which results in the same shutdown. The sensor survey period is *5 seconds*, i.e. activation occurs after six missed measurements.

Failing checks:

Inconsistent reStructuredText 09/13/2026
User avatar mt:libretranslate

Suggestion added

If the sensor does not respond, the platform `dallas temp` publishes the value ``NaN`` and the lambda function turns off the relay.

Suggested change:

If the sensor does not respond, the platform `dallas temp` publishes the value ``NaN`` and the lambda function turns off the relay.

Failing checks:

Inconsistent reStructuredText 09/13/2026
User avatar mt:libretranslate

Suggestion added

Emergency shutdown of the heater is implemented by two mechanisms:

Suggested change:

Emergency shutdown of the heater is implemented by two mechanisms:
09/13/2026
User avatar mt:libretranslate

Suggestion added

Between the thresholds *25 °C* and *25.5 °C*, no action is performed - this is the hysteresis zone in which the relay retains its state. The state of the relay is checked before switching, so there are no unnecessary publications of the state.

Suggested change:

Between the thresholds *25 °C* and *25.5 °C*, no action is performed - this is the hysteresis zone in which the relay retains its state. The state of the relay is checked before switching, so there are no unnecessary publications of the state.
09/13/2026
User avatar mt:libretranslate

Suggestion added

Hysteresis is calculated in the lambda function at each measurement, not by the “on value range” trigger. The reason for this is how this trigger works: it remembers whether the previous value was within the range, and the values of "NaN" skip without changing this feature. As a result, after disconnecting and reconnecting the sensor, the input to the range would not be detected and the heater would remain off.

Suggested change:

Hysteresis is calculated in the lambda function at each measurement, not by the “on value range” trigger. The reason for this is how this trigger works: it remembers whether the previous value was within the range, and the values of "NaN" skip without changing this feature. As a result, after disconnecting and reconnecting the sensor, the input to the range would not be detected and the heater would remain off.

Failing checks:

Inconsistent reStructuredText 09/13/2026
User avatar mt:libretranslate

Suggestion added

jxd r6 e1eth lcd thermostat.yaml

Suggested change:

jxd r6 e1eth lcd thermostat.yaml
09/13/2026
User avatar mt:libretranslate

Suggestion added

:download:` Download jxd r6 e1eth lcd thermostat.yaml <jxd_r6_e1eth_lcd_thermostat.yaml>`

Suggested change:

:download:` Download jxd_r6_ r6 e1eth_lcd_ lcd thermostat.yaml <jxd_r6_e1eth_lcd_thermostat.yaml>`

Failing checks:

Inconsistent reStructuredText 09/13/2026
User avatar mt:libretranslate

Suggestion added

In the example setting *25 °C*, hysteresis *0.5 °C*: the heater is turned on at a temperature below *25 °C* and is turned off at a temperature above *25.5 °C*.

Suggested change:

In the example setting *25 °C*, hysteresis *0.5 °C*: the heater is turned on at a temperature below *25 °C* and is turned off at a temperature above *25.5 °C*.
09/13/2026
User avatar mt:libretranslate

Suggestion added

The relay ``1` controls the heater according to the indications of the temperature sensor *1-Wire*: the relay is turned on below the setting, and above it is turned off. So that the relay does not click when the temperature fluctuates near the setting, the on and off thresholds are spaced by the amount of hysteresis.

Suggested change:

The relay ``1` controls the heater according to the indications of the temperature sensor *1-Wire*: the relay is turned on below the setting, and above it is turned off. So that the relay does not click when the temperature fluctuates near the setting, the on and off thresholds are spaced by the amount of hysteresis.

Failing checks:

Inconsistent reStructuredText reStructuredText syntax error 09/13/2026
User avatar mt:libretranslate

Suggestion added

Thermostat

Suggested change:

Thermostat
09/13/2026
User avatar mt:libretranslate

Suggestion added

The "on release" trigger is not used: the state is switched only at the moment of pressing.

Suggested change:

The "on release" trigger is not used: the state is switched only at the moment of pressing.

Failing checks:

Inconsistent reStructuredText 09/13/2026
User avatar mt:libretranslate

Suggestion added

jxd r6 e1eth lcd buttons.yaml

Suggested change:

jxd r6 e1eth lcd buttons.yaml
09/13/2026
User avatar mt:libretranslate

Suggestion added

:download:` Download jxd r6 e1eth lcd buttons.yaml <jxd_r6_e1eth_lcd_buttons.yaml>`

Suggested change:

:download:` Download jxd_r6_ r6 e1eth_lcd_ lcd buttons.yaml <jxd_r6_e1eth_lcd_buttons.yaml>`

Failing checks:

Inconsistent reStructuredText 09/13/2026
User avatar mt:libretranslate

Suggestion added

With each closure of the input, the corresponding relay changes the state to the opposite. Suitable for buttons without fixation and pass switches.

Suggested change:

With each closure of the input, the corresponding relay changes the state to the opposite. Suitable for buttons without fixation and pass switches.
09/13/2026
User avatar mt:libretranslate

Suggestion added

Control of light buttons without fixation

Suggested change:

Light control with momentary buttControl of light buttons without fixations
09/13/2026
User avatar mt:libretranslate

Suggestion added

Relays remain available for control from *Home Assistant*, but the next time the input state changes, they will return to the state specified by the input.

Suggested change:

Relays remain available for control from *Home Assistant*, but the next time the input state changes, they will return to the state specified by the input.
09/13/2026
User avatar mt:libretranslate

Suggestion added

jxd r6 e1eth lcd switches.yaml

Suggested change:

jxd r6 e1eth lcd switches.yaml
09/13/2026
User avatar mt:libretranslate

Suggestion added

:download:` Download jxd r6 e1eth lcd switches.yaml <jxd_r6_e1eth_lcd_switches.yaml>`

Suggested change:

:download:` Download jxd_r6_ r6 e1eth_lcd_ lcd switches.yaml <jxd_r6_e1eth_lcd_switches.yaml>`

Failing checks:

Inconsistent reStructuredText 09/13/2026